The tengels can, depending on the size, be apart between 6 mm. Ask us if you doubt!Ĭaution! The bottom batten has a shorter heart to heart distance as the other battens. This depends on the slope of the roof, windload, lenght of the roof, etcetera. It is therefore possible, depending on the project, to increase These were calculated once for Scandinavia where there is a higher snow load than in the Netherlands. Nautracom Stanacol ® Long Roof tile sheet: 400 mm Nautracom Stanacol ® Roof tile sheet: 350 mm If the interval is 1200 mm then you should use a 32x100 cm decking. Folding is made easier by using a wooden board.Ī 22 x 100 cm board is sufficient as decking if the beams are at intervals of 900 mm. Start by attaching the foil below the roof near the gutter to the ridge in parallel jobs.Ī 50 mm opening must be left open between the corner and the batten to make ventilation possible or you should use micro perforated foil.Īt the end the foil can be folded back till a height of 30 mm and attatched to the eave. The foil is designed to prevent theįormation of condensation and to prevent moisture from penetrating into the insulation. We recommend the use of foil as there is reason to believe that there is insufficient ventilation in the space below the roof. Ventilation openings must be at the top of the ridge.Ī minimum of 50 mm are left open between the foil and the insulation. The space to ventilate should be constructed so that air can flow freely from the gutter to the ridge. This can be achieved through proper insulation, the assembly of a moisture-proof barrier and proper ventilation. Temperature under the roof is the same as the outside. Condensation can be prevented by making sure that the This moisture can condense under the roof. Heat and moisture from the underlying spaces always rises to the roof. Consider, especially at a low angled roofs, sufficient overlap so that no water can push up the sheet. Piece, such as 14 meter length, it is necessary to order in two lengths. If it is not possible to produce a sheet in one If a roof is measured, it is best to lay out the dimensions of graphic paper, so as to facilitate this calculation. Sometimes yoy will have to cut extra sheet on the sides away when total width of the roof is less than the It means you need for this roof 14 sheets of a certain length. Stanacol ® roof tile sheet: effective width 1100 mm. ![]() The number of sheets needed for a roof can be calculated by the width of the roof divided by the effectiveĮxample: width of roof = 15 meter. Nautracom tile sheets will be delivered at the ordered length. Scratches can be repaired on the spot by using retouch paint in the same color as the sheets. The galvanized coating on the sheets will prevent rust. If in doubt you can always contact us for advice.ĭuring the assembly you might cause some scratching on the sheets for instance by your tools. Some aggressive cleaners mayĭamage the top coating. The use of ordinary soaps and detergents is possible. Parts and dust from sawing and drilling should be removed from the sheet, because these particles can rust and can damage the surface coating of the sheet.ĭirt that is eventually located on the sheets can simply be hosed away with water. Removed, so rust in those spots will occur! Never cut the sheets with a simple grinder, jig saw or angle grinder, as this will damage the top coating of the sheet and the galvanized layer of the steel sheet gets If the sheets should be cutĪlways use a nibbler or a special metal blade. In some cases (pass through or corners) some cutting has to be done on the roof. Nautracom tile panels are custom cut delivered. The sheets must then be separated with slats between them, so there is ventilation between the sheets. When the sheets are stored under poor conditions, like rain or frost, or should be kept for more than one month, the package must be opened. Under normal circumstances, the tile sheets from Nautracom can be stored one month in theįactory packaging. Read the instructions carefully before starting the installation of the tile sheets. The instructions cover normal roof types that are common in the Netherlands. ![]() This page contains general information how to install the Nautracom Stanacol ® and Nautracom Stanacol ® Long tile sheets to the roof. You'll probably need more time with fitting in comparison to an assembly company with experienced staff that is daily installating sheets. You do not have to be an expert to get our plates installed on the roof. With this we hope to reduce errors during the installation or even prevent errors.įor a DIY job tile sheets are suitable. On this page the text of our installation instructions for the Stanacol ® Tile Sheets. Installation Instructions Stanacol ® Roof Tile sheets
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |